Humans can perform ghost imaging, no computer required

Ghost imaging involves capturing an image using photons that have never interacted with the object being imaged. Can you perform ghost imaging using the human eye as one of the detectors? The answer is, apparently, yes. Researchers stared down the barrel of one of their own imaging setups and claimed to observe images. In doing so, they’ve shown that the eye is much like any other camera.

Ghost imaging isn’t all that ghostly

In ghost imaging’s original conception, the quantum properties of light were an essential part of the imaging process. The basic idea was that two entangled photons would be separated. One would head off to bounce off the object being imaged. The other would go to a camera. The photon that bounced off the object would hit a photodiode (essentially a single pixel detector). That click would then be used to trigger the camera to record the other photon, the one that hadn’t hit the object. Supposedly thanks to entanglement, an image can slowly be constructed from light that has never been near the object being imaged.

As cool as that sounds, ghost imaging isn’t necessarily quantum. Images can be constructed by summing up a sequence of patterns. Each pattern is assigned a value called a weight. If a pattern contributes strongly to creating an image, then it gets a large weight, while patterns that do not contribute get a very small weight.

As it turns out, the entangled photons were sending a random selection of patterns to the object and the camera. The photodiode clicks more often when a pattern contributes strongly to the reflections from the object. The image at the camera has a large contribution from that pattern because it is triggered by the photodiode.

The role of “quantum” was to ensure that both photons had the same pattern. But you don’t need entangled photons to do that.

Although it still retains the name, ghost imaging is nothing like its original conception now. It can be performed using things like light-emitting diodes rather than expensive entangled photon sources. The patterns are deliberately generated using the same sort of active mirrors that are used in projection systems. About the only bit remaining from the original setup is a single photodiode that is used to detect the reflected light intensity at a single point.

You don’t even need two beams of light. Instead, the image is reconstructed by a computer. The computer adds all the patterns together, with each pattern being given a weighting (think brightness) determined from the strength of the photodiode signal. You put in light, you detect at a single point, perform some trickery on a computer, and out comes an image.

Taking the computer out of the equation

In this work, researchers have used a clever trick (while clever, in hindsight it seems pretty obvious) to eliminate the computer from the process.

The light is still projected onto an active mirror that generates patterns. The patterned light is sent to the object and detected by a photodiode. The photodiode signal controls the brightness of a second light source. That light source is projected onto a second active mirror that is producing the same patterns.

The patterns from the second mirror are either viewed directly or are projected onto a screen for someone to view. It is then up to the eye to add all the patterns up.

The patterns used here are not a raster scan of the object (though they could be). If you remember cathode ray tubes, then you will know that static images can be impressed upon the brain, even if each pixel is independently lit up in a sequential fashion, rather than all being illuminated at once. You just have to run through them all fast enough that the eye and brain lie to each other and staple all the dots together into one image.

Ghost imaging is slightly different. In a raster scan, the image is built up sequentially from top left to bottom right. You can imagine that each cone or rod (the eye’s detectors) is always getting a full blast of light from just a tiny portion of that image, leaving the brain to join the dots.

In ghost imaging, though, the patterns are complex, so each cone and rod receives multiple blasts of light as we cycle through the pattern. It was not certain that the brain and eye could successfully integrate the more complex patterns to form an image. It is also unlike a movie, where each image is slightly different, and the brain interpolates to provide a nice, smooth motion. In this case, it is more like wildly different images are projected one after the other, and the eye and brain are expected to smoothly combine them.

And they do.

To give you an idea of how fast your nervous system is operating: the patterns would be seen as individual images if they are separated by more than about 20ms. It takes around 200 patterns, all of which should be projected within about a 50ms window, to create a low-resolution image.

So what’s it all about?

Ghost imaging with the human eye is a funny combination of the obvious, the non-obvious, and the interesting. It seems, on the face of it, pretty obvious that hooking the photodiode up to the light source should project the pattern sequence in the right order and intensity. It is not exactly obvious that the eye and brain should integrate the pattern sequence the way it does.

Must Read

error: Content is protected !!